LED Lighting Drivers: PLN100 100w Power Supplies

100W Single Output LED Lighting Power Supply

	Universal AC input
	Protections: Short Circuit/ Overload/ Over voltage/ Over temperature
	IP64 design for indoor or outdoor installations
	Built-in active Power Factor Correction function
	Cooling by free air convection
	UL1310 Class 2 power unit

Model Number	DC Voltage Adjust (typ.)	Output Voltage	Output Amps	Ripple and Noise	Over Voltage Protection	Efficiency
PLN100-12	10.2~12Volts(DC)	12 Volts(DC)	5.0 Amps (Note 5)	150mVpk-pk (Note 1)	13~16Volts(DC) Shutdown and latch off o/p voltage, re-power	83%
PLN100-15	12.8~15Volts(DC)	15 Volts(DC)	5.0 Amps (Note 5)	150mVpk-pk (Note 1)	16.5~20Volts(DC) Shutdown and latch off o/p voltage, re-power	85%
PLN100-20	17~20Volts(DC)	20 Volts(DC)	4.8 Amps (Note 5)	150mVpk-pk (Note 1)	22~27Volts(DC) Shutdown and latch off o/p voltage, re-power	87%
PLN100-24	20.4~24Volts(DC)	24 Volts(DC)	4.0 Amps (Note 5)	150mVpk-pk (Note 1)	27~34Volts(DC) Shutdown and latch off o/p voltage, re-power	87%
PLN100-27	23~27Volts(DC)	27 Volts(DC)	3.55 Amps (Note 5)	150mVpk-pk (Note 1)	29~36Volts(DC) Shutdown and latch off o/p voltage, re-power	87%
PLN100-36	30.6~36Volts(DC)	36 Volts(DC)	2.65 Amps (Note 5)	150mVpk-pk (Note 1)	39~48Volts(DC) Shutdown and latch off o/p voltage, re-power	87%
PLN100-48	40.8~48Volts(DC)	48 Volts(DC)	2.0 Amps (Note 5)	200mVpk-pk (Note 1)	52~64Volts(DC) Shutdown and latch off o/p voltage, re-power	87%

PLN100 series

Input Specifications

Input Voltage Range	90-264VAC, 127~370Volts(DC) (Note 4)
Input Current	12Volts(DC) 0.8 Amps/115VAC; 0.4 Amps/230VAC 15Volts(DC) 0.9Amps/115VAC; 0.4Amps/230VAC 20~48Volts(DC) 1.1Amps/115VAC; 0.55Amps/230VAC
Frequency Range	47-63 Hz
Inrush Current	40 Amps @ 230VAC (Cold start)
Leakage Current	< 0.75mA / 240VAC
DC Voltage Adjust (typ.)	10.2~12Volts(DC)
Power Factor Correction	PF> 0.95/ 230VAC; >0.95/ 115VAC ?0.9 at 75~100%load

General Specifications

Isolation	3750VAC Input - Output; 1880VA; Input - Ground; 500VAC Output - Ground
Efficiency	83%
Safety Approvals	UL1310 Class 2, EN61347-1 EN61347-2-13 independent, UL60950-1, UL879 (listed in UL SAM) TUV EN60950-1, CAN/CSA C22.2 No. 223-M91(except for 48V) (Note 8)
Insulation Resistance	?100M?/500 Volts / 25°C / 70%RH
EMI	Compliance to EN55015 EN55022B(CISPR22B)
EMS	Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN55024, EN61547, light industry level (surge 4KV) criteria A
Harmonic Current	Compliance to EN61000-3-2C (>75% load); EN61000-3-3

Environmental Specifications

Operating Temperature	-30°C to +50°C (See Derate Curve)
Storage Temperature	-40°C to +80°C, 10~95% RH
Relative Humidity	20 to +95% RH non cond
MTBF	303.1KHrs min, MIL-HDBK-217F(25°C)
Vibration	10~500Hz, 2G10min./1cycle, period for 72min. each along X, Y, Z axes
Cooling	free air convection
IP Rating	IP64
Temperature Coefficient	±0.03% / °C (0-50°C)

Output Specifications

Output Voltage	12 Volts(DC)
Output Amps	5.0 Amps (Note 5)
Load Regulation	±2%
Line Regulation	±1.0%
Ripple and Noise	150mVpk-pk (Note 1)
Over Voltage Protection	13~16Volts(DC) Shutdown and latch off o/p voltage, re-power
Current Adjustment Range	Can be adjust by internal potential meter SVR2 (Note 6)
Over Current Protection	95~102% Constant current limiting,auto recov
Over Temperature Protection	90°C ±10°C (RTH2) Shutdown o/p voltage, auto recover
Short Circuit Protection	Hiccup mode, auto recover (Note 3)
Hold Up Time	60mS/230VAC; 30mS/115VAC
LED Voltage Operation
Rise Time	1200mS, 80mS / 230VAC & 115VAC
Voltage Tolerance	±3%: 12~27Volts ; ±2%: 36~48Volts (Note 2)

Physical Specifications

Size (mm)	200 x 70.5 x 35 mm
Size (Inches)	7.87”x2.77”x 1.38”)
Weight (g)	520g
Weight (oz)	18.34 oz

Notes

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regulation.

3. Please refer to OLP characteristics.

4. Derating may be needed under low input voltage. Please check the derating curve for more details.

5. This is the maximum possible output current and power. Over load protection may be activated slightly below this level to comply with the requirement of UL1310 class 2.

6. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications,

but please

reconfirm special electrical requirements for some specific system design.

8. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.

All specifications are typical at nominal input, full load, and 25°C unless otherwise noted

Astrodyne products are not authorized or warranteed for use as critical components in life support systems, equipment used in hazardous environments, nuclear controls systems, or other mission-critical applications.

Power Supply Search

PLN100 100w Constant Current LED/Lighting Power Supplies