DRT480 480w Power Supplies

480W Three Phase Industrial DIN RAIL Power Supply

	Three-Phase AC340 ~ 550V wide range input
	High efficiency 89% and low dissipation
	Protections; Short circuit / Over load/ Over voltage / Over temperature
	Cooling by free air convection
	Built-in constant current limiting circuit
	Can be installed on DIN rail TS-35/7.5 or 15, UL508(industrial control equipment) approved, EN61ooo-6-2 (EN50082-2) industrial immunity level, 100% full load burn-in test

Model Number	Output Voltage	Output Amps	Over Voltage Protection	DC Voltage Adjust	Minimum Load Requirement	Efficiency
DRT-480-24	24V	20A	30~36V Shut down o/p voltage, re-power on to recover	24~48V	0~20A	89% typ.
DRT-480-48	48V	10A	59~66V Shut down o/p voltage, re-power on to recover	48~55V	0~10A	90% typ.

DRT-480 series

Input Specifications

Input Voltage Range	Three-Phase 340~550VAC 480~780VDC
Frequency Range	47 ~ 63Hz
Inrush Current	Cold start 50A typ.
Input Current	1.7A/400VAC 1.3A/500VAC typ.
Leakage Current	<3.5mA / 530VAC

General Specifications

Isolation	3KVAC (Note 4)
Isolation Input-Ground	1.5KVAC (Note 4)
Isolation Output-Ground	0.5KVAC (Note 4)
Insulation Resistance	100M Ohms/500VDC (Note 4)
Efficiency	89% typ.
Safety Approvals	UL508, UL60950-1, TUV EN60950-1 Approved
Harmonic Current	Compliance to EN61000-3-2,-3 (Note 4)

Environmental Specifications

Operating Temperature	-20°C to +70°C (Refer to output load derating curve)
Storage Temperature	-40 ~ +85°C
Working Humidity	20~90% RH non condensing
Storage Humidity	10 ~ 95% RH
EMI	Compliance to EN55011 (CISPR11), EN55022(CISPR22), EN61204-3 Class B (Note 4)
MTBF	91.1Khrs min. MIL-HDBK-217F (25°C)
Vibration	Component: 10~500HX, 2G 10min/1 cycle, 60min, each along X, Y ,Z axes: Mounting: Compliance to IEC60068-2-6
EMS	Compiance to EN61000-4-2, 3, 4, 5, 6. 8, 11, ENV50204-3, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A (Note 4)

Output Specifications

Output Voltage	24V
Output Amps	20A
Load Regulation	± 0.5%
Line Regulation	± 0.5%
Temperature Coefficient	± 0.03% / °C (0-50°C)
Ripple and Noise	80mVp-p max. (Note 2)
Over Voltage Protection	30~36V Shut down o/p voltage, re-power on to recover
Over Current Protection	105 ~ 150% rated output power Constant current limiting, recovers automatically after fault condition is removed
Over Temperature Protection	100°C ±5°C (TSW: Detect on heatsink of power switch) Shut down o/p voltage, recovers automatically after temperature goes down
Voltage Tolerance	± 1.0% (Note 3)
DC Voltage Adjust	24~48V
Minimum Load Requirement	0~20A
Rise Time	1200ms, 40ms/400VAC 800ms,40ms/500VAC at full load
Hold Up Time	16ms/400VAC 35ms/500VAC at full load typ.

Physical Specifications

Size (mm)	227x125.2x100mm
Weight (g)	2.5Kg; 6pcs/16Kg/1.75CUFT

Notes

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature.

2. Ripple and noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equpiment must be re-confirmed that it still meets EMC directives.

5. Dual phase operation: derating of 20% is required.

All specifications are typical at nominal input, full load, and 25°C unless otherwise noted

Astrodyne products are not authorized or warranteed for use as critical components in life support systems, equipment used in hazardous environments, nuclear controls systems, or other mission-critical applications.

Power Supply Search

DRT480 480w Power Supplies